$92.50
On Hold
New 4 port 4CH 10 100M PoE Switch Hub 10M 100M Support Power over Ethernet 15.4W
The 4CH PoE network switch which is designed specifically for Telecom carrier. The device implemented more sufficient and advanced MCU control technology. which has efficient protection of each port. It is used with wireless AP, IP cameras, VOIP and other device that support power over Internet.
Support IEEE802.3af , IEEE802.3at, Single port output max 15.4W
RJ-45 port support Auto MDI/MDI-X End-Span/ Middle-Span
Embedded 4-port PoE, 1-port uplink
10/100Mbps duplex, half-duplex
Back-plane (Switching Fabric): 1.0Gbps
1K MAC Address Table
Network transmission distance extend to 150M, total 300M
Extensive status indication. ALARM: general alarm indicator, if any failure of equipment, ALARM red lights flash; working status indication for each port, it turns green when normal, abnormal blinking.
More effective protection circuit. Output protection on each port, short circuit, overload protection. When any power output short circuit or overload, the protect circuit is active, and the corresponding alarm indicator light flashes. Meanwhile all other output port is not affected.
Total power overload protection. When sum of all port power is over the total power limit; to ensure that the device work normally, it will shut off the power port of high port number. This ensure that the equipment will not exceed the total power ,otherwise will caused the entire device to stop working.
The device support 4port, output 25W max per port.
Wall Mount Design
System reliability MTBF>100k hour
Comes with AC/DC adapter
Performance Specifications
Bandwidth：1.6 Gbps
Network latency：Less than 20 μs for 64-byte frames in store-and-forward mode for 100 Mbps to 100 Mbps transmission
Buffer memory：96 KB embedded memory per unit
Address database size：1,000 media access control (MAC) addresses per system
Addressing：48-bit MAC address
Mean Time Between Failure (MTBF)：190,000 hours (~ 21 years)
Acoustic Noise： 0 dB
Network Protocol and Standards
IEEE802.3af , IEEE802.3at
Status LEDs
System: Power, PoE Maximum Power
Per Port: Link, Activity, Speed, PoE Active, PoE Fault
Power Supply
Total Power Consumption: 60 W maximum
PoE Watt budget: 56W
IEEE802.3af Power Consumption: 56 W maximum (Ports 1 – 4)
48VDC, 1.25A power output; plug is localized to country of sale
Physical Specifications
Dimensions (H x W x D)：28 x 118 x 85mm
Environmental Specifications
Operating temperature: 0 to 55 DegC
Operating humidity: 90% maximum relative humidity, non-condensing
Electromagnetic Emissions
CE mark, commercial
FCC Part 15 Class B
VCCI Class B: EN 55022 （CISPR 22）， Class B
CTick: EN 55024
Safety: CE Mark ,commercial CE/LVD EN60950
Package Contents
5-PORT 10/100 SWITCH WITH 4-PORT POE
AC Adapter
Wall-mount kit
Installation guide
Support IEEE802.3af , IEEE802.3at, Single port output max 15.4W
RJ-45 port support Auto MDI/MDI-X End-Span/ Middle-Span
Embedded 4-port PoE, 1-port uplink
10/100Mbps duplex, half-duplex
Back-plane (Switching Fabric): 1.0Gbps
1K MAC Address Table
Network transmission distance extend to 150M, total 300M
Extensive status indication. ALARM: general alarm indicator, if any failure of equipment, ALARM red lights flash; working status indication for each port, it turns green when normal, abnormal blinking.
More effective protection circuit. Output protection on each port, short circuit, overload protection. When any power output short circuit or overload, the protect circuit is active, and the corresponding alarm indicator light flashes. Meanwhile all other output port is not affected.
Total power overload protection. When sum of all port power is over the total power limit; to ensure that the device work normally, it will shut off the power port of high port number. This ensure that the equipment will not exceed the total power ,otherwise will caused the entire device to stop working.
The device support 4port, output 25W max per port.
Wall Mount Design
System reliability MTBF>100k hour
Comes with AC/DC adapter
Performance Specifications
Bandwidth：1.6 Gbps
Network latency：Less than 20 μs for 64-byte frames in store-and-forward mode for 100 Mbps to 100 Mbps transmission
Buffer memory：96 KB embedded memory per unit
Address database size：1,000 media access control (MAC) addresses per system
Addressing：48-bit MAC address
Mean Time Between Failure (MTBF)：190,000 hours (~ 21 years)
Acoustic Noise： 0 dB
Network Protocol and Standards
IEEE802.3af , IEEE802.3at
Status LEDs
System: Power, PoE Maximum Power
Per Port: Link, Activity, Speed, PoE Active, PoE Fault
Power Supply
Total Power Consumption: 60 W maximum
PoE Watt budget: 56W
IEEE802.3af Power Consumption: 56 W maximum (Ports 1 – 4)
48VDC, 1.25A power output; plug is localized to country of sale
Physical Specifications
Dimensions (H x W x D)：28 x 118 x 85mm
Environmental Specifications
Operating temperature: 0 to 55 DegC
Operating humidity: 90% maximum relative humidity, non-condensing
Electromagnetic Emissions
CE mark, commercial
FCC Part 15 Class B
VCCI Class B: EN 55022 （CISPR 22）， Class B
CTick: EN 55024
Safety: CE Mark ,commercial CE/LVD EN60950
Package Contents
5-PORT 10/100 SWITCH WITH 4-PORT POE
AC Adapter
Wall-mount kit
Installation guide
HK, NT